收藏本站

ADM1192
VOLTAGE AND CURRENT READBACK
The ADM1192 contains the components to allow voltage and
current readback over an I 2 C bus. The voltage output of the
current sense amplifier and the voltage on the VCC pin are fed
into a 12-bit ADC via a multiplexer. The device can be instructed
to convert voltage and/or current at any time during operation
via an I 2 C command. When all conversions are complete, the
voltage and/or current values can be read back with 12-bit
accuracy in two or three bytes.
Data Sheet
The peripheral whose address corresponds to the transmitted
address responds by pulling the data line low during the
low period before the ninth clock pulse, known as the
acknowledge bit, and holding it low during the high period
of this clock pulse. All other devices on the bus now remain
idle while the selected device waits for data to be read from
it or written to it. If the R/W bit is 0, the master writes to
the slave device. If the R/W bit is 1, the master reads from
SERIAL BUS INTERFACE
Control of the ADM1192 is carried out via the serial system
management bus (I 2 C). This interface is compatible with the I 2 C
fast mode (400 kHz maximum). The ADM1192 is connected to
this bus as a slave device, under the control of a master device.
IDENTIFYING THE ADM1192 ON THE I 2 C BUS
The ADM1192 has a 7-bit serial bus slave address. When the
device powers up, it does so with a default serial bus address.
The five MSBs of the address are set to 01011; the two LSBs are
determined by the state of the ADR pin. There are four config-
urations available on the ADR pin that correspond to four I 2 C
addresses for the two LSBs (see Table 5). This scheme allows four
ADM1192 devices to operate on a single I 2 C bus.
GENERAL I 2 C TIMING
Figure 18 and Figure 19 show timing diagrams for general write
and read operations using the I 2 C. The I 2 C specification defines
conditions for different types of read and write operations, which
are discussed in the Write and Read Operations section. The
general I 2 C protocol operates as follows:
1. The master initiates a data transfer by establishing a start
condition, defined as a high-to-low transition on the serial
data line, SDA, while the serial clock line, SCL, remains
high. This indicates that a data stream is to follow. All slave
peripherals connected to the serial bus respond to the start
condition and shift in the next eight bits, consisting of a 7-bit
slave address (MSB first) plus an R/W bit that determines the
direction of the data transfer, that is, whether data is written to
or read from the slave device (0 = write, 1 = read).
Table 5. Setting I 2 C Addresses via the ADR Pin
2.
3.
the slave device.
Data is sent over the serial bus in sequences of nine clock
pulses: eight bits of data followed by an acknowledge bit
from the slave device. Data transitions on the data line must
occur during the low period of the clock signal and remain
stable during the high period because a low-to-high transition
when the clock is high can be interpreted as a stop signal.
If the operation is a write operation, the first data byte after
the slave address is a command byte. This tells the slave
device what to expect next. It can be an instruction, such as
telling the slave device to expect a block write, or it can be
a register address that tells the slave where subsequent data
is to be written.
Because data can flow in only one direction, as defined by
the R/W bit, it is not possible to send a command to a slave
device during a read operation. Before performing a read
operation, it may be necessary to first execute a write
operation to tell the slave what sort of read operation to
expect and/or the address from which data is to be read.
When all data bytes are read or written, stop conditions are
established. In write mode, the master pulls the data line
high during the 10 th clock pulse to assert a stop condition.
In read mode, the master device releases the SDA line
during the SCL low period before the ninth clock pulse,
but the slave device does not pull it low. This is known as a
no acknowledge. The master then takes the data line low
during the SCL low period before the 10 th clock pulse, and
then high during the 10 th clock pulse to assert a stop
condition.
Base Address
01011
ADR Pin State
Ground
Resistor to ground
Floating
High
ADR Pin Logic State
00
01
10
11
Address in Binary 1
0101100X
0101101X
0101110X
0101111X
Address in Hex
0x58
0x5A
0x5C
0x5E
1
X = don’t care.
Rev. D | Page 10 of 20
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
EVAL-ADM1275EBZ BOARD EVALUATION FOR ADM1275
EVAL-ADM1276EBZ BOARD EVAL FOR ADM1276
EVAL-ADM2483EBZ BOARD EVAL FOR ADM2483
EVAL-ADM2485EB5Z BOARD EVAL FOR ADM2485
EVAL-ADM2486EBZ BOARD EVAL FOR ADM2486
EVAL-ADUM3221AEBZ BOARD EVAL FOR ADUM3220/ADUM3221
EVAL-ADUM3471EBZ EVALUATION MODULE FOR ADUM3471
EVAL-ADUM4160EBZ EVALUATION MODULE FOR ADUM4160
相关代理商/技术参数
EVAL-ADM1275EBZ 功能描述:BOARD EVALUATION FOR ADM1275 RoHS:是 类别:编程器，开发系统 >> 评估演示板和套件 系列:- 标准包装:1 系列:- 主要目的:电信，线路接口单元（LIU） 嵌入式:- 已用 IC / 零件:IDT82V2081 主要属性:T1/J1/E1 LIU 次要属性:- 已供物品:板，电源，线缆，CD 其它名称:82EBV2081
EVAL-ADM1276EBZ 功能描述:BOARD EVAL FOR ADM1276 RoHS:是 类别:编程器，开发系统 >> 评估演示板和套件 系列:* 标准包装:1 系列:- 主要目的:电信，线路接口单元（LIU） 嵌入式:- 已用 IC / 零件:IDT82V2081 主要属性:T1/J1/E1 LIU 次要属性:- 已供物品:板，电源，线缆，CD 其它名称:82EBV2081
EVAL-ADM2481EBZ 功能描述:BOARD EVAL FOR ADM2481 RoHS:是 类别:编程器，开发系统 >> 评估演示板和套件 系列:* 标准包装:1 系列:- 主要目的:电信，线路接口单元（LIU） 嵌入式:- 已用 IC / 零件:IDT82V2081 主要属性:T1/J1/E1 LIU 次要属性:- 已供物品:板，电源，线缆，CD 其它名称:82EBV2081
EVAL-ADM2482EEB3Z 功能描述:BOARD EVAL FOR ADM2482 RoHS:是 类别:编程器，开发系统 >> 评估演示板和套件 系列:- 标准包装:1 系列:- 主要目的:电信，线路接口单元（LIU） 嵌入式:- 已用 IC / 零件:IDT82V2081 主要属性:T1/J1/E1 LIU 次要属性:- 已供物品:板，电源，线缆，CD 其它名称:82EBV2081
EVAL-ADM2482EEB5Z 功能描述:BOARD EVAL FOR ADM2482 RoHS:是 类别:编程器，开发系统 >> 评估演示板和套件 系列:- 标准包装:1 系列:- 主要目的:数字电位器 嵌入式:- 已用 IC / 零件:AD5258 主要属性:- 次要属性:- 已供物品:板 相关产品:AD5258BRMZ1-ND - IC POT DGTL I2C1K 64P 10MSOPAD5258BRMZ10-ND - IC POT DGTL I2C 10K 64P 10MSOPAD5258BRMZ100-ND - IC POT DGTL I2C 100K 64P 10MSOPAD5258BRMZ50-ND - IC POT DGTL I2C 50K 64P 10MSOPAD5258BRMZ1-R7-ND - IC POT DGTL I2C 1K 64P 10MSOPAD5258BRMZ10-R7-ND - IC POT DGTL I2C 10K 64P 10MSOPAD5258BRMZ50-R7-ND - IC POT DGTL I2C 50K 64P 10MSOPAD5258BRMZ100-R7-ND - IC POT DGTL I2C 100K 64P 10MSOP
EVAL-ADM2483EBZ 功能描述:BOARD EVAL FOR ADM2483 RoHS:是 类别:编程器，开发系统 >> 评估演示板和套件 系列:* 标准包装:1 系列:- 主要目的:电信，线路接口单元（LIU） 嵌入式:- 已用 IC / 零件:IDT82V2081 主要属性:T1/J1/E1 LIU 次要属性:- 已供物品:板，电源，线缆，CD 其它名称:82EBV2081
EVAL-ADM2484EEBZ 功能描述:BOARD EVAL FOR ADM2484 RoHS:是 类别:编程器，开发系统 >> 评估演示板和套件 系列:iCoupler® 标准包装:1 系列:- 主要目的:电信，线路接口单元（LIU） 嵌入式:- 已用 IC / 零件:IDT82V2081 主要属性:T1/J1/E1 LIU 次要属性:- 已供物品:板，电源，线缆，CD 其它名称:82EBV2081
EVAL-ADM2485EB3Z 功能描述:BOARD EVAL FOR ADM2485 RoHS:是 类别:编程器，开发系统 >> 评估演示板和套件 系列:* 标准包装:1 系列:- 主要目的:电信，线路接口单元（LIU） 嵌入式:- 已用 IC / 零件:IDT82V2081 主要属性:T1/J1/E1 LIU 次要属性:- 已供物品:板，电源，线缆，CD 其它名称:82EBV2081